Raised Floor

We, at Noor Al Khaldiah believe that our clients deserve the best quality and cost effective materials, and so we have invested in dealerships from the world leader manufacturer of flooring tiles, we have a wide range of tiles used in data centers, telecommunication environments, military command centers and modern office buildings, as well as perforated raised floor used for under floor air conditioner system. With removable panels, the raised access a floor facilitate the access to the area below and is an investment never lost that can be reinstalled to a different place with different sets of bearing load.

 

We have a variety of panels made from different materials with specific finishes to meet the needs of our clients as follow:

 

  • Bare Panel Steel Cementation

  • Calcium Sulphate

  • Wood Core

  • Cable Management System

  • Perforated panels

 

PANELS

The core material of panels is high density and load resistant special product “chipboard”. The thickness is applied 30 or 38 mm according to the purpose of use. The standard size of the panels is 600x600 mm.
If required, it can be produced with 400x600 mm special size and
with the understructure stringer or without it. The angle on the edge of panels not only provides easy fitting but also provides easier access to the system under the floor.

 


Top Surface Coverings:


One of the most important features of the raised floors is providing
rich covering alternatives. By covering the surface of chipboard with
a variety of materials such as laminate, pvc, aluminum sheet or foil,
sheet steel and carpet, users’ needs are met totally.

 


Bottom Surface Coverings:


The material used at the bottom of the panel changes according to the class of required load. There are alternatives as 0,5 mm thick sheet steel, 0,2 mm thick aluminum sheet or 0,05 mm thick aluminum foil, according to their high resistance, protection against moisture, conductivity or antistatic features.

 


Panel Tests:


Formfloor marked panels have been tested and approved by the
expert foundations in our country and abroad. Load bearing,
fire-resistance, corrosion-resistance, electrical conductivity and
antistatic features have been certified by institutions like England
authorized laboratories, METU and TSE.
Our company keeps on research and developing activities in its own
laboratories.

• All experiments are carried out in accordance with EN 12825 Standard.


• The working load is evaluated by dividing the ultimate load to the k=3 safety factor.


• Residual deflection, permitted by the Standard, is 0,5 mm at most.


• All panels’ dimensional deviation class is 1.


• Load bearing tests are carried out on 32 cm height systems without stringers.

CLASSES OF LOAD AND DEFLECTION ACCORDING TO
EN 12825 STANDARD:

Laminated Covered Panels (HPL)

Core Material : According to the desired load capacity, 30 or 38 mm thick and min 650 kg/m3 density chipboard is used.


Top Covering : 1 mm thick, overlay covered HPL laminate resistant to abrasion.


Bottom Covering : Depending on the needs, 0,5 mm thick sheet steel, 0,2 mm thick aluminum sheet or 0,05 mm thick aluminum foil are used.


Edge Covering : 0,4 mm thick hard PVC. It can be applied in colors appropriate to the top covering.

PVC Covered Panels

Core Material : According to the desired load capacity, 30 or 38 mm thick and min 650 kg/m3 density chipboard is used.


Top Covering : In various thicknesses and as appropriate to the aim, PVC can be used in features like homogeneous, heterogeneous, antistatic, conductive, linoleum, etc.


Bottom Covering : Depending on the needs, 0,5 mm thick sheet steel, 0,2 mm thick aluminum sheet or 0,05 mm thick aluminum foil are used.


Edge Covering : 0,4 mm thick hard PVC. It can be applied in colors appropriate to the top covering.

Galvanized Sheet Steel Covered Panels

Core Material : According to the desired load capacity, 30 or 38 mm thick and min 650 kg/m3 density chipboard is used.


Top Covering : 0,5 mm thick sheet steel. It is used in places where high resistance required, and is suitable for covering with carpet.


Bottom Covering : 0,5 mm thick sheet steel.


Edge Covering : 0,4 mm thick hard PVC.

Aluminum Sheet/ Foil Covered Panels

Aluminum Sheet
 

Core Material : According to the desired load capacity, 30 or 38 mm thick and min 650 kg/m3 density chipboard is used.


Top Covering : 0,2 mm thick aluminum sheet. It is an ideal solution for bare or carpet covered places.


Bottom Covering : Depending on the needs, 0,5 mm thick sheet steel, 0,2 mm thick aluminum sheet or 0,05 mm thick aluminum foil are used.


Edge Covering : 0,4 mm thick hard PVC.

Aluminum Foil
 

Core Material : According to the desired load capacity, 30 or 38 mm thick and min 650 kg/m3 density chipboard is used.


Top Covering : 0,05 mm thick aluminum foil/0,2 mm thick aluminum sheet is generally used in places to be covered with carpet.


Bottom Covering : Depending on the needs, 0,5 mm thick sheet steel, 0,2 mm thick aluminum sheet or 0,05 mm thick aluminum foil are used.


Edge Covering : 0,4 mm thick hard PVC.

Understructure

No collapse for the pedestals under four times the working load according to the Standard EN 12825.

M14 Pedestal Heights

M14 Technical Features

Tests

Accessories

CONTACT US

Email:      info@nourk.com
Phone:    +971 6 573 3610

Fax:        +971 6 573 3642

Address:  Suite# 1204, Al Batha Tower, Buheira Corniche, Sharjah - United Arab Emirates, P.O.Box 68650

  • w-facebook
  • Twitter Clean

© by Noor Al Khaldiah